REIGN Functional Trainer Power Rack

A REIGN power rack with two 90kg cable stacks built into its sides, so barbell work and cable work share one compact footprint.

Most home gyms have a rack in one corner and either a separate cable machine or no cables at all. The Again Faster® REIGN Functional Trainer Power Rack puts both in one frame that takes up just 1340 x 810mm of floor. Squat, bench and press in the rack, pull up on the integrated bar, then use the two adjustable pulley stations for rows, flyes, pressdowns and single-arm work, without walking across the room or loading a single plate.

View in 3D or see it in your room (AR)

Why a rack with built-in cable stacks?

• Two machines, one footprint. The weight stacks sit inside the sides of the rack, so you get a functional trainer without giving up a second area of floor.
• Faster supersets. Pin the stack and go. There are no plates to load between exercises, so you can pair a barbell lift with a cable movement and keep the rest periods short.
• Small, steady jumps. The 2:1 ratio means each 4.5kg plate adds 2.25kg at the handle, which suits rehab, isolation work and single-arm training.
• Room to grow. The frame takes the full REIGN accessory range, from spotter arms and dip station to monolifts and jammer arms.

Who it is for

• Home and garage gyms that want a proper rack and cables without the depth of a full rear-stack trainer.
• PT studios and small facilities that need an all-in-one station for clients, from strength work to rehab.
• Lifters who train accessories properly, not just the main lifts.

What you can train

• In the rack: back squat, front squat, bench press, overhead press, rack pulls.
• On the bar: pull-ups, chin-ups, hanging knee raises.
• On the cables: standing and kneeling rows, chest flyes and crossovers, tricep pressdowns, face pulls, curls, woodchops, Pallof presses, glute kickbacks and single-arm work, with the pulleys set high, low or anywhere in between.

How it compares

Prefer stacks behind the rack and a dedicated lat pulldown? See the REIGN Rear Functional Trainer Rack. Only need cables? The REIGN Mounted Cable Rack sits 629mm off the wall.

The rack

• 60 x 60mm uprights in 3mm steel, with 17mm holes, so it takes the full REIGN attachment range.
• Westside hole spacing: 25mm through the bench zone for precise J-cup and spotter heights, and 50mm elsewhere.
• Integrated 32mm pull-up bar.
• J-cups with UHMW liners to protect your barbell.
• Plate storage on both sides.
• Bolt-down design for stability.

The cable system

• Two independent stations, each with its own 90kg stack (20 x 4.5kg plates).
• 2:1 ratio: a full stack gives 45kg at the handle, in 2.25kg steps.
• Pulley carriages adjust up and down the uprights, so you can set each cable high, low or anywhere in between.
• Slide bushings and hard-chromed solid steel guide rods keep the stacks running smoothly, even when loaded.
• Double ball-bearing pulleys with wide V-grooves for safe, smooth cable travel.
• Stretch-free steel cables with a plastic coating.

Will it fit your space?

• Footprint: 1340mm wide x 810mm deep. Leave room around it to load the bar, use the cables and walk out of the rack.
• Height: 2153mm to the top of the uprights and 2210mm at the highest point, which is the top pulleys. Allow a little extra ceiling clearance for fitting and for pull-ups.
• Floor: it must be bolted to a solid, level floor.

What is included

• REIGN Series Half Power Rack with integrated pull-up bar
• 1 pair of J-cups
• 2 x REIGN weight stack pulley systems
• 2 x 90kg weight stacks (40 x 4.5kg plates in total)
• Plate storage on both sides

Add a bench, spotter arms, a dip station and other REIGN attachments in the Build Your Package options above.

Specifications

FAQs

What does a 2:1 ratio mean?
The resistance at the handle is half the weight selected on the stack. A full 90kg stack gives 45kg at the handle, and each 4.5kg plate adds 2.25kg. It feels lighter than the number on the pin, but it gives smoother, longer cable travel and smaller jumps in weight.

How tall is it?
The frame is 2153mm tall. The top pulleys sit above the uprights, so the highest point is 2210mm. Plan for 2210mm plus a little clearance.

Can I use my own attachments?
The uprights are 60 x 60mm with 17mm holes, the REIGN Series standard. REIGN attachments fit directly. Attachments from other brands only fit if they are made for 60 x 60mm uprights and 17mm holes, so check their specification first.

Does it need to be bolted down?
Yes. Bolt it to a solid, level floor for stability.

Can I use my own barbell and bench?
Yes. Any standard Olympic barbell works on the J-cups, and you can add a bench in the Build Your Package options above.

How is it delivered?
On a pallet. The rack, the two pulley systems and the weight plates arrive boxed for home assembly.

This REIGN Series rack is also compatible with our full range of REIGN Accessories.